Industrial dehumidification system.
CDM-138L is a large capacity portable type industrial dehumidification system. And, this is one of few units with high capacity and inbuilt tank. Please note, dehumidification itself is a broad term. Hence, it needs to understand and address with proper research. CDM-138L unit designed for industrial and pool dehumidification. Thus, let’s know this model in detail.
Some of the uses need a unit temporarily but with a high rating. For example, flood disaster recovery requires a strong dehumidifier for short use. For such a case, you need a unit with an internal container. It is not practical to arrange a drainage point for such interim use. CDM-138L commercial dehumidification system fills this gap. CtrlTech offers this product in UAE, Saudi Arabia, Oman, and Qatar.
Industrial dehumidification system features.
Two sought after feature of CDM-138L is its capacity and robustness. The body casing made up of metal with powder coating. Thus, it can withstand rough use. The compressor uses R410a gas. Hence, it is proactive towards climate saving. Besides, a centrifugal fan saves more power. The fan has a copper sealed motor based on Bessel duct design. As a result, there will be less wind loss and delivers more air.
It has a large container to collect condensate water during the process. Also, the unit can connect to the drain point. With an internal tank, it is ready to use at any site. By pressing push lock at front, the tank can be accessed. Intake air has to pass through a dense filter. And, air get discharge from the side grills. With the help of four wheels, the system easy to displace. A panel of this industrial dehumidification system located on topside.
Addon features.
Internal memory saves the configuration you make. Thus, the unit starts with the same settings when it starts again. It saves lots of time. Many times, the CDM-138L system fix at remote sites. At such places, the auto-restart feature is handy. The unit starts itself when the power comes back. As required for the condensation unit, it has an auto defrost mechanism.
Condenser fitted with copper piping. Hence, the system is more efficient. Inside the unit, dry and wet sections separated. Also, it has independent electronic control. As a consequence, this system becomes reliable. Maintainance of this unit is very simple. To access internal spares, we need to open only one panel. For the best result, place this industrial dehumidification system with clearance. It is a plug-n-play device. It does not require any installation.
Industrial dehumidification system control panel.
CDM-138L has simple, useful, and easy to use panel. Hence, any staff at the site can operate this system. The user panel fitted on top for easy access. Buttons label itself explains its function. In short, each button is well defined. It has an LED display for current humidity. In the same vein, it shows room temperature also. Also, it has LEDs for defrosting, power on, a tank full, and timer.
CO button turns unit in continuous drying mode. It means the system will not cut off at a set level. In contrast, with the set button, we can set cut off humidity levels. With the add and subtract button, users can set the desired moisture level. Thus, the unit stops itself when room humidity lower than the set value. For drying clothes, the machine can set to high airflow and 50% RH to dry cloths. Comfort mode saves power. In this mode, the industrial dehumidification system set at 60% RH. And, fan set at low speed.
USPs of CDM-138L.
- Body made of metal. Thus, the unit can combat against shocks and impacts.
- With a large tank, it can set up and remove with ease.
- For safety, the machine stops when the bucket gets full. Also, it glows ups tank full sign.
- It can set configuration with outage memory built inside.
- One button press mode selection. So, it is easy to use.
- To save power, users can set a delay on or off timer.
- Electronic control with wet and dry separation design makes the unit reliable.
- The machine is easy to maintain with high energy efficiency. Hence, the unit has a low running cost.
Manukumar –
We are an electro mech contractor in Kuwait. We used this portable industrial dehumidifier for drying concrete at our site. It helped us save lots of time by quick drying.
Lamis Charrouf –
We are producing drugs in Abu Dhabi, UAE. We are using CtrlTech dehumidifiers for a long time. Their products are economical and reliable. Thanks for your prompt service.
Basilio Fuellas –
This industrial dehumidifier helped to reduce humidity in our medical waste storage room. We are using it for the last year.
Faisal Hyder –
We used this machine at a hotel project at Palm Jumeirah, Dubai. This dehumidifier quickly removed fungus and terrible smell.
Ahmed Dyab –
We buy this industrial dehumidification system for our factory in Riyadh, Saudi Arabia. This unit is very powerful and effective.
Rajesh Unnithan –
We installed this portable dehumidifier in a switchgear room in Muscat, Oman. Happy to inform you that it is keeping humidity low in the place.
Abdulla Al Ibrahim –
We supply equipment to ARAMCO in Jeddah, Saudi Arabia. Thanks to CtrlTech for offering such an excellent commercial dehumidifier.
Ajith Ninan –
Purchase CDM-138L commercial dehumidifier from CtrlTech Dubai. We are happy with performance of this industrial dehumidifier. Prompt service and delivery.
Syed Jasim –
We are using this large capacity dehumidifier for our cold storage in Abu Dhabi. This system works excellently in the pharmaceutical industry.
Michelle Moreno –
CtrlTech offered us a good industrial dehumidifier at the right prices. And most importantly, they are offering us good service, which includes free standby units.
Mike Callender –
This dehumidifier is very useful to control humidity inside the warehouse. It solved the issue of moisture in our warehouse in Dubai. It is a good product.
Jaison Yesudasan –
We are using this industrial dehumidifier for a marine ship halted in Marama port Bahrain. We succeeded in maintaining low humidity inside the boat with the help of this machine.